Barfusz, O.; van der Velden, T.; Brepols, T.; Reese, S.:
Gradient-extended damage analysis with reduced integration-based solid-shells at large deformations
Computer Methods in Applied Mechanics and Engineering, Volume 389, 1 February 2022, 114317 DOI: 10.1016/j.cma.2021.114317

Zielinski, T.; Vovk, A.; Riemer, O.; Karpuschewski, B.:
Influence of local material loads on surface topography while machining steel 42CrMo4 and Inconel 718
Procedia CIRP 108 (2022), 412-417. DOI: 10.1016/j.procir.2022.03.064

Tausendfreund, A.; Frerichs, F.; Stöbener, D.; Fischer, A.:
Experimental validation of workpiece deformation simulations by means of rigorous boundary condition analysis
Procedia CIRP 108 (2022), 341-345 DOI: 10.1016/j.procir.2022.02.197

Eckert, S.:
Laser-Induced Thermochemical Polishing of Metals
BIAS Verlag Band 75, Dissertation

Simons, M.; Radel, T.:
Influence of electrolyte concentration on laser chemical machining
LAF 2022

Schneider, S.; Herrig, T.; Klink, A.; Bergs, T.:
Modeling of the temperature field induced during electrical discharge machining
CIRP Journal of Manufacturing Science and Technology 38 (2022), 650–659 DOI: 10.1016/j.cirpj.2022.05.012

Herrig, T.; Heidemanns, L.; Ehle, L.; Weirich, T.E.; Bergs, T.:
Surface Integrity of Wire Electrochemical Machined Inconel 718
Procedia CIRP 108 (2022), 152-157 DOI: 10.1016/j.procir.2022.04.069.

Oßwald, K.; Schneider, S.; Klink, A.; Bergs, T.:
White Layer Thickness Variation in Die Sinking EDM
Procedia CIRP 113 (2022), 5-9 DOI: 10.1016/j.procir.2022.09.111

Hess, R.; Grethe, P.; Heidemanns, L.; Herrig, T.; Klink, A.; Bergs, T.:
Simulation based derivation of changed rim zone properties caused by thermal loadings during EDM process
Procedia CIRP 113 (2022), 41-46 DOI: 10.1016/j.procir.2022.09.117

Heidemanns, L.; Herrig, T.; Klink, A.; Bergs, T.:
Thermographic in-situ investigation of precise electrochemical machining
Procedia CIRP 113 (2022), 404-409 DOI: 10.1016/j.procir.2022.09.191

Klink, A.; Schneider, S.; Bergs, T.:
Development of a process signature for electrical discharge machining
CIRP Annals 71 (2022) 1, 177-180 DOI: 10.1016/j.cirp.2022.03.043

Eich, M.; Karahan, A.; Ljatifi, B.; Langenhorst, L.; Meyer, D.; Heinzel, C.:
Simulation of internal material loads caused by simultaneous contacts in grinding with predominantly mechanical impact
Procedia CIRP 108 (2022), 352-357 DOI: 10.1016/j.procir.2012.03.058

Gierden, C.; Kochmann, J.; Waimann, J.; Svendsen, B.; Reese, S.:
A review of FE-FFT-Based Two-Scale Methods for Computational Modeling of Microstructure Evolution and Macroscopic Material Behavior
Archives of computational methods in engineering 29 (2022), 4115-4135 DOI: 10.1007/s11831-022-09735-6

Waimann, J.; Reese, S.:
Variational modeling of temperature induced and cooling-rate dependent phase transformations in polycrystalline steel
Mechanics of Materials 170 (2022), 104299 DOI: 10.1016/j.mechmat.2022.104299

Waimann, J.; Gierden, C.; Schmidt, A.; Svendsen, B.; Reese, S.:
Reduced FFT-Based Simulation of a Mechanically Loaded Clustered Microstructure Using an Adaptive Set of Fourier Modes
Key Engineering Materials 926 (2022), 2285-2292 DOI: 10.4028/p-9cr29c

Gierden, C.; Waimann, J.; Svendsen, B.; Reese, S.:
Using a reduced set of Fourier modes in terms of a FFT-based microstructure simulation
8th European Congress on Computational Methods in Applied Sciences and Engineering (2022) DOI: 10.23967/eccomas.2022.284

Gierden, C.; Waimann, J.; Reese, S.:
Simulation of phase transformations in polycrystalline shape memory alloys using fast Fourier transforms
8th European Congress on Computational Methods in Applied Sciences and Engineering (2022) DOI: 10.23967/eccomas.2022.250

van der Velden, T.; Ritzert, S.; Reese, S. Waimann, J.:
A novel numerical strategy for modeling the moving boundary value problem of electrochemical machining
International journal for numerical methods in engineering 124 (2022) 8, 1856-1882 DOI: 10.1002/nme.7190

Felder, S.; Kopic-Osmanovic, N.; Holthusen, H.; Brepols, T.; Reese, S.:
Thermo-mechanically coupled gradient-extended damage-plasticity modeling of metallic materials at finite strains
International Journal of Plasticity 148 (2022). 103142 DOI: 10.1016/j.ijplas.2021.103142

Hoja, S.; Nadolski, D.; Steinbacher, M.; Fechte-Heinen, R.:
Optimized nitriding for subsequent induction heat treatment
HTM J. Heat Treatm. Mat. 76 (2021) 4, akzeptiert

Sommer, M.; Hoja, S.; Steinbacher, M.; Fechte-Heinen, R.::
Investigation of Compound Layer Structures after Nitriding and Nitrocarburizing of Quenched and Tempered Steels
HTM J. Heat Treatm. Mat. 76 (2021) 3, 219-236 DOI: 10.1515/htm-2021-0005

Bergs, T.; Röttger, J.; Barth, S.; Prinz, S.:
Approach to the numerical modelling of the chip temperatures in single grain scratching
Prod. Eng. 2021, 677-681 DOI: 10.1007/s11740-021-01017-7

Dadgar, M.; Schreiner, T.; Schüler, M.; Herrig, T.; Bergs, T.:
An Improved Model for Contour Damage Compensation in 3D Waterjet Machining
Procedia CIRP (2021), akzeptiert

Schüler, M.; Dadgar, M.; Herrig, T.; Bergs, T.:
Influence of Abrasive Properties on Erosion in Waterjet Machining
Procedia CIRP (2021), akzeptiert

Schüler, M.; Dadgar, M.; Herrig, T.; Klink, A.; Bergs, T.:
Experimental Investigation of Abrasive Properties in Waterjet Machining
Procedia CIRP (2021), akzeptiert

Schüler, M.; Heidrich, D.; Herrig, T.; Fang, X.F.; Bergs, T.:
Automotive hybrid design production and effective end machining by novel abrasive water jet technique
Procedia CIRP (2021), akzeptiert

Friederici, V.; Schumacher, J.; Clausen, B.:
Influence of local differences in microstructure and hardness on the fatigue behaviour of a slewing bearing steel
Procedia Structural Integrity 31 (2021), p. 8-14, ISSN 2452-3216 DOI: 10.1016/j.prostr.2021.03.003

Vovk, A.; Dehkordi, A. P.; Glüge, R.; Karpuschewski, B.; Sölter, J.:
Modification of the Johnson–Cook Material Model for Improved Simulation of Hard Milling High-Performance Steel Components
Appl. Mech. 2 (2021), 571-580 DOI: 10.3390/applmech2030032

Barfusz, O.; van der Velden, T.; Brepols, T.; Reese, S.:
Reduced integration-based solid and solid-shell finite elements for gradient-extended damage
Proc. Appl. Math. Mech. 2021;21:1 e202100057 DOI: 10.1002/pamm.202100057

Waimann, J.; Gierden, C.; Schmidt, A.; Svendsen, B.; Reese, S.:
FFT-based homogenization using a reduced set of frequencies and a clustered microstructure
Proc. Appl. Math. Mech. 2021;21:1 e202100241 DOI: 10.1002/pamm.202100241

Gierden, C.; Waimann, J.; Svendsen, B.; Reese, S.:
A model order reduction technique for FFT‐based microstructure simulation using a geometrically adapted reduced set of frequencies
Proceedings in applied mathematics and mechanics 21 (2021) 1, e202100061 DOI: 10.1002/pamm.202100061

Zander, D.; Schupp, A.; Beyss, O.; Rommes, B.; Klink, A.:
Oxide Formation during Transpassive Material Removal of Martensitic 42CrMo4 Steel by Electrochemical Machining
Materials 14 (2021) 402 DOI: 10.3390/ma14020402

Zander, D.; Schupp, A.; Mergenthaler, S.; Pütz, R.; Altenbach, C.:
Impact of rim zone modifications on the surface finishing of ferritic–pearlitic 42CrMo4 using electrochemical machining
Materials and Corrosion 72 (2021), 995-1009 DOI: 10.1002/maco.202012213

Maradia, U.; Filisetti, E.; Wiessner, M., Schneider, S., Boccadoro, M.:
The influence of energy input characteristics on surface integrity in wire EDM
Procedia CIRP 95 (2020), pp. 268-272 DOI: 10.1016/j.procir.2020.01.004

Bergs, T.; Mohammadnejad, M.; Hess, R.; Heidemanns, L.; Klink, A.:
Simulation of the Evolutions in Real Microstructure of Material under Thermal Cycle with High Thermal Gradients
Procedia CIRP 95 (2020), 238-243 DOI: 10.1016/j.procir.2020.01.149

Petersen, T.; Ahmed, S.; Kunieda, M.; Klink, A.:
Observation of EDM plasma behavior influenced by parasitic working gap capacitance
Procedia CIRP 95 (2020), 189-194 DOI: 10.1016/j.procir.2020.01.198

Bergs, T.; Schüler, M.; Dadgar, M.; Herrig, T.; Klink, A.:
Investigation of Waterjet Phases on Material Removal Characteristics
Procedia CIRP 95 (2020), 12-17 DOI: 10.1016/j.procir.2020.02.319

Klink, A.; Harst, S.; Olivier, M.; Tombul, U.; Bergs, T.:
High Entropy Alloy machining by EDM and ECM
Procedia CIRP 95 (2020), 178-182 DOI: 10.1016/j.procir.2020.01.318

Bergs, T.; Rommes, B.; Kohls, E.; Meyer, H.; Klink, A.; Heidemanns, L.; Harst, S.:
Experimental Investigation concering the Influence of Electrochemical Machining on Process Chain induced Residual Stress States
Procedia CIRP 95 (2020), 726-730 DOI: 10.1016/j.procir.2020.01.170

Gadeschi, G. B.; Schilden, T.; Albers, M.; Vorspohl, J.; Meinke, M.; Schröder, W.:
Direct particle-fluid simulations of flushing flow in electrical discharge machining
Journal of Engineering Applications of Computational Fluid Mechanics 15 (2021) 1, 328-343 DOI: 10.1080/19942060.2021.1877198

Gräbner, D.; Zielinski, T.; Vovk, A.; Riemer, O.; Karpuschewski, B.; Lang, W.:
An Investigation on High-Resolution Temperature Measurement in Precision Fly-Cutting
MDPI Sensors 21 (2021) 1530 DOI: 10.3390/s21041530

Jaworek, D.; Waimann, J.; Reese, S.:
A variational concept and its experimental calibration for temperature‐induced rate‐dependent phase transformations in steel
Proceedings in Applied Mathematics and Mechanics 20(1) (2020), e20200319 DOI: 10.1002/pamm.202000319

Waimann, J.; Gierden, C.; Schmidt, A.; Svendsen, B.; Reese, S.:
Microstructure simulation using self-consistent clustering analysis
Proceedings in Applied Mathematics & Mechanics 20(1) DOI: 10.1002/pamm.202000263

Frerichs, F.; Lu, Y.; Lübben, T.; Radel, T.:
Process Signature for Laser Hardening
Metals 2021, 11, 465 DOI: 10.3390/met11030465

Schupp, A.; Beyss, O.; Rommes, B.; Klink, A.; Zander, D.:
Insights on the Influence of Surface Chemistry and Rim Zone Microstructure of 42CrMo4 on the Efficiency of ECM
Materials 14 (2021) 14, 2132 DOI: 10.3390/ma14092132

Strunk, R.; Borchers, F.; Clausen, B.; Heinzel, C.:
Influence of Subsequently Applied Mechanical and Thermal Loads on Surfaces Ground with Mechanical Main Impact
Materials 14 (2021) 2386 DOI: 10.3390/ma14092386

Mohammadnejad, M.:
Phase Field Simulation of Microstructure Evolutions in the Heat Affected Zone of a Spark-Eroded Workpiece
Dissertation RWTH Aachen 2020; Apprimus Verlag ISBN: 978-3-86359-946-1

Barfusz, O.; van der Velden, T.; Brepols, T.; Holthusen, H.; Reese, S.:
A reduced integration-based solid-shell finite element formulation for gradient-extended damage
Comput. Methods Appl. Mech. Engrg.;Elsevier;2021;Vol. 382 DOI: 10.1016/j.cma.2021.113884

Zielinski, T.; Vovk, A.; Riemer, O.; Karpuschewski, B.:
An Investigation on Internal Material Loads and Modifications in Precision Turning of Steel 42CrMo4
MDPI Micromachines 112 (2021), 526 DOI: 10.3390/mi12050526

Schweickhardt, L.; Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Noise reduction in high-resolution speckle displacement measurements through ensemble averaging
Applied Optics 60(7):1871-1880, 2021 DOI: 10.1364/AO.416028

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
In-Process Measurement of Three-Dimensional Deformations Based on Speckle Photography
Applied Sciences 11:4981 (11 pp.), 2021 DOI: 10.3390/app11114981

Ehle, L.C., Spille, J., Meyer, H., Kämmler, J., Werner, J., Schwedt, A., Epp, J., Weirich, T.E., Mayer, J.:
Controlled twinning and martensitic transformation in metastable AISI D3 (X210Cr12) steel by sequential deep rolling and liquid nitrogen cooling
Materials Today Communications 28 (2021) 102484 DOI: 10.1016/j.mtcomm.2021.102484

Simons, M.; Beste, L.; Radel, T.:
Laserchemische Mikrobearbeitung von Inconel 718
Mikroproduktion 2021 (03/21), 26-27

Lu, Y.; Ehle, L.C.; Richter, S.; Radel, T.:
Influence of multi-pass laser hardening of normalized AISI 4140 on the grain size
Surface & Coatings Technology 421 (2021), 127434 DOI: 10.1016/j.surfcoat.2021.127434

Barfusz, O.; van der Velden, T.; Brepols, T.; Reese, S.:
Towards forming simulations by means of reduced integration-based solid-shell elements considering gradient-extended damage
IOP Conf. Ser.: Mater. Sci. Eng. 1157 012029; 2021 DOI: 10.1088/1757-899X/1157/1/012029

van der Velden, T.; Rommes, B.; Klink, A.; Reese, S.; Waimann, J.:
A novel approach for the efficient modeling of material dissolution in electrochemical machining
International Journal of Solids and Structures 229 (2021), 111106 DOI: 10.1016/j.ijsolstr.2021.111106

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Speckle photographic in-process measurement of three-dimensional deformations in running manufacturing processes
Proc. SPIE 11782, Optical Measurement Systems for Industrial Inspection XII, 1178205 DOI: 10.1117/12.2592284

Schweickhardt, L.; Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Speckle pattern modulation for high-resolution displacement measurements
Proc. SPIE 11782, Optical Measurement Systems for Industrial Inspection XII, 117820D DOI: 10.1117/12.2591847

Kohls, E.; Heinzel, C.; Eich, M.:
Evaluation of Hardness and Residual Stress Changes of AISI 4140 Steel Due to Thermal Load during Surface Grinding
J. Manuf. Mater. Process. 73 (2021) 5 DOI: 10.3390/jmmp5030073

Borchers, F.; Clausen, B.; Ehle, L.; Eich, M.; Epp, J.; Frerichs, F.; Hettig, M.; Klink, A.; Kohls, E.; Lu, Y.; Meyer, H.; Rommes, B.; Schneider, S.; Strunk, R.; Zielinski, T.:
The Influence of Former Process Steps on Changes in Hardness, Lattice and Micro Structure of AISI 4140 Due to Manufacturing Processes
Metals 11 (2021) 1102 DOI: 10.3390/met11071102

Eckert, S.; Vollertsen, F.; Schupp, A.; Zander, D.; Rommes, B.; Klink, A.:
Understanding the Influence of Chemical and Thermal Loads on the Productivity for Processing 42CrMo4 Steel and Titanium via Laser-Induced Thermochemical Machining
Procedia CIRP (2021), akzeptiert

Gierden, C.; Waimann, J.; Svendsen, B.; Reese, S.:
FFT-based simulation using a reduced set of frequencies adapted to the underlying microstructure
Computer methods in materials science 21 (2021), 51-58 DOI: 10.7494/cmms.2021.1.0742

Karpuschewski, B.; Lübben, T.; Meinke, M.; Eckert, S.; Frerichs, F.; Schneider, S.; Klink, A.; Langenhorst, L.; Sölter, J.:
Comparison of Process Signatures for thermally dominated processes
CIRP J. Manuf. Sci.Technol. 35 (2021), 217-235 DOI: 10.1016/j.cirpj.2021.06.013

Kinner-Becker, T.; Hettig, M.; Sölter, J.; Meyer, D.:
Analysis of internal material loads and Process Signature Components in deep rolling
CIRP J. Manuf. Sci. Technol. (2021), akzeptiert

Kuschel, S.; Kinner-Becker, T.; Zmich, R.; Sölter, J.; Meyer, D.:
Modelling and Simulation of Mechanical Loads and Residual Stresses in Deep Rolling
J. Manuf. Mater. Process. (2021), akzeptiert

Schneider, S.; Vorspohl, J.; Frerichs, F.; Klink, A.; Meinke, M.; Schröder, W.; Lübben, T.:
Investigation on residual stress induced by multiple EDM discharges
Procedia CIRP (2021), akzeptiert

Schneider, S.:
Modellierung der Energiedissipation in der Funkenerosion
Dr.-Ing. Dissertation, RWTH Aachen (2021), akzeptiert

Schupp, A.; Pütz, R.D.; Beyss, O.; Beste, L.; Radel, T.; Zander, D.:
Change of oxidation mechanisms by laser chemical machined rim zone modifications of 42CrMo4 steel
Materials (2021), akzeptiert

Zmich, R.; Meyer, D.:
Thermal effects on surface and subsurface modifications in laser-combined deep rolling process
J. Manuf. Mater. Process. 55 (2021) 5 DOI: 10.3390/jmmp5020055

Gierden, C.; Waimann, J.; Svendsen, B.; Reese, S.:
A geometrically adapted reduced set of frequencies for a FFT-based microstructure simulation
Computer methods in applied mechanics and engineering 386 (2021), 114131 DOI: 10.1016/j.cma.2021.114131

Lu, Y.; Meyer, H.; Radel, T.:
Influence of multi-pass laser hardening on residual stress and distortion
Lasers in Manufacturing Conference Proceeding (2021), akzeptiert

Van der Velden, T.; Rommes, B.; Klink, A.; Reese, S.; Waimann, J.:
Efficient modeling of material dissolution in electrochemical machining
Proc. Appl. Math. Mech. 2021;21:1 e202100042 DOI: 10.1002/pamm.202100042

Eich, M.; Borchers, F.; Langenhorst, L.; Karahan, A.; Heinzel, C.:
Simulation of internal material loads caused by multiple contacts in grinding with predominantly mechanical impact
Procedia CIRP (2021), akzeptiert

Petersen, T.; Schneider, S.; Klink, A.; Bergs, T.:
Modelling of Energy Distribution in SEDM on the Basis of Gas Bubble Observations
Procedia CIRP (2021), akzeptiert

Heinzel, C.; Heinzel, J.; Guba, N.; Hüsemann, T.:
Comprehensive Analysis of the Thermal Impact and its Depth Effect in Grinding
Annals of the CIRP 70 (2021) 1, 289-292, akzeptiert

Kinner-Becker, T.; Zmich, R.; Sölter, J.; Meyer, D.:
Combined laser and deep rolling process as a means to study thermo-mechanical processes
Procedia CIRP (2021), akzeptiert

Vovk, A.; Sölter, J.; Karpuschewski, B.:
Numerical investigation of the influence of multiple loads on material modifications during hard milling
Procedia CIRP (2021), akzeptiert

Vovk, A.; Glüge, R.; Karpuschewski, B.; Sölter, J.:
Wechselverfestigung beim Fräsen von Stahl
WT WerkstattsTechnik 9 (2021), akzeptiert

Ehle, L.C.:
Randschichtmodifikationen erzeugt durch mechanische, thermische und chemische Wirkung verschiedener Herstellungsprozesse am 42CrMo4 Stahl
PhD (2021), Shaker Verlag ISBN: 978-3-8440-7938-8 DOI: 10.2370/9783844079388

Gräbner, D.:
Materialintegrierte Messung von mechanischen Größen: Sensoren und Anwendungen
Dr.-Ing. Dissertation, Universität Bremen, 2021 DOI: 10.26092/elib/768

Bergs, T.; Hardt, M.; Schraknepper, D.:
Determination of Johnson-Cook material model parameters for AISI 1045 from orthogonal cutting tests using the Downhill-Simplex algorithm
Procedia Manufacturing. Jg. 48, 2020, Nr. 4, 541-552 DOI: 10.1016/j.promfg.2020.05.081

Bergs, T.; Schüler, M.; Herrig, T.; Fernolendt, J.; Linde, M.:
Systematic Change of Abrasive Size Distribution: Advances in Water Jetting
Springer Nature, 2020, 39-48 DOI: 10.1007/978-3-030-53491-2_4

Ehle, L.; Schneider, S.; Schwedt, A.; Richter, S.; Klink, A.; Mayer, J.:
Electron microscopic characterization of surface zones thermo-chemically modified by electrical discharge machining
Journal of Materials Processing Tech. 280 (2020), 116596 DOI: 10.1016/j.jmatprotec.2020.116596

Meyer, H.; Epp, J.:
Spatial Internal Material Load and Residual Stress Distribution Evolution in Synchrotron In Situ Investigations of Deep Rolling
Quantum Beam Science, 2020, 4. Jg., Nr. 1, S. 3. DOI: 10.3390/qubs4010003

Jaworek, D.; Waimann, J.; Gierden, C.; Wulfinghoff, S.; Reese, S.:
A Hashin-Shtrikman type semi-analytical homogenization procedure in multiscale modeling to account for coupled problems
Technische Mechanik 40(1) (2020), 46-52 DOI: 10.24352/UB.OVGU-2020-012

Waimann, J.; Reese, S.; Junker, P.:
Variational material modeling of the transformation induced plasticity in polycrystalline steel
Technische Mechanik 40(1) (2020), 87-96 DOI: 10.24352/UB.OVGU-2020-017

Ehle, L.; Strunk, R.; Borchers, F.; Schwedt, A.; Clausen, B.; Mayer, J.:
Influence of process chains with thermal, mechanical and thermo-mechanical impact on the surface modifications of a grind-strengthened 42CrMo4 steel
Procedia CIRP 87 (2020) 426-431 DOI: 10.1016/j.procir.2020.02.088

Willert, M.; Zielinski, T.; Rickens, K.; Riemer, O.; Karpuschewski, B.:
Impact of ultrasonic assisted cutting of steel on surface integrity
Procedia CIRP 87 (2020), 222-227 DOI: 10.1016/j.procir.2020.05.135

Karpuschewski, B.; Beutner, M.; Eckebrecht, J.; Heinzel, J.; Hüsemann, T.:
Surface integrity aspects in gear manufacturing
Procedia CIRP 87 (2020), 3-12 DOI: 10.1016/j.procir.2020.05.112

Kinner-Becker, T.; Sölter, J.; Karpuschewski, B.:
A simulation-based analysis of internal material loads and material modifications in multi-step deep rolling
Procedia CIRP 87 (2020), 515-520 DOI: 10.1016/j.procir.2020.02.060

Borchers, F.; Meyer, H.; Heinzel, C.; Meyer, D.; Epp, J.:
Development of surface residual stress and surface state of 42CrMo4 in multistage grinding
Procedia CIRP 87 (2020), 198-203 DOI: 10.1016/j.procir.2020.02.095

Eckert, S.; Vollertsen, F.:
Prozessbeschleunigung beim laserchemischen Polieren
LASER MAGAZIN 2 (2020), 20-23

Borchers, F.;Clausen, B.; Eckert, S.; Ehle, L.; Epp, J.; Harst, S.; Hettig, M.;Klink, A.; Kohls, E.; Meyer, H.; Meurer, M.; Rommes, B.; Schneider, S.; Strunk, R.:
Comparison of Different Manufacturing Processes of AISI 4140 Steel with Regard to Surface Modification and Its Influencing Depth
Metals 10 (2020) 895, 1-27 DOI: 10.3390/met10070895

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
In-process workpiece displacement measurements under the rough environments of manufacturing technology
Procedia CIRP 87 (2020), p. 409-414 DOI: 10.1016/j.procir.2020.02.080

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Messung thermomechanischer Beanspruchungen in laufenden Schleifprozessen
tm - Technisches Messen 87(3), p. 201-209 DOI: 10.1515/teme-2019-0133

Frerichs, F.; Lübben, T.:
Influence of Initial Microstructure on Manufacturing Processes with Thermal Loads accompanied by Hardening
Procedia CIRP 87 (2020), 521-526 DOI: 10.1016/j.procir.2020.02.075

Vovk, A.; Sölter, J.; Karpuschewski, B.:
Finite element simulations of the material loads and residual stresses in milling utilizing the CEL method
Procedia CIRP 87 (2020), 539-544 DOI: 10.1016/j.procir.2020.03.005

Kohls, E.; Zmich, R.; Heinzel, C.; Meyer, D.:
Residual stress change in multistage grinding
Procedia CIRP 87 (2020), 186-191 DOI: 10.1016/j.procir.2020.02.068

Hettig, M.; Meyer, D.:
Sequential multistage deep rolling under varied contact conditions
Procedia CIRP 87 (2020), 291-296 DOI: 10.1016/j.procir.2020.02.027

Vorspohl, J.; Frerichs, F.; Schneider, S.; Meinke, M.; Schröder, W.; Lübben, Th.; Klink, A.:
Determination of residual stresses in processes with multiple thermal loads
Procedia CIRP 87 (2020), 509-514 DOI: 10.1016/j.procir.2020.02.066

Jaworek, D.; Gierden, C.; Kinner-Becker, T.; Waimann, J.; Reese, S.:
Modeling Material Modifications Using a Process Independent Approach
Procedia Manufacturing 47 (2020), 1442-1448 DOI: 10.1016/j.promfg.2020.04.314

Bergs, T.; Mohammadnejad, M.; Witteler, M.; Heidemanns, L.; Klink, A.:
Experimental Investigation on Process Signature for EDM Process
Procedia CIRP 95 (2020), 726-730 DOI: 10.1016/j.procir.2020.01.170

Bergs, T.; Harst, S.:
Development of a process signature for electrochemical machining
CIRP Annals Manufacturing Technology 69 (2020), 153-156 DOI: 10.1016/j.cirp.2020.04.078

Lu, Y.; Meyer, H.; Radel, T.:
Multi-cycle phase transformation during laser hardening of AISI 4140
Procedia CIRP 94 (2020), p. 919-923 DOI: 10.1016/j.procir.2020.09.073

Barfusz, O.; Brepols, T.; van der Velden, T.; Frischkorn, J.; Reese, S.:
A single Gauss point continuum finite element formulation for gradient-extended damage at large deformations
Comput. Methods Appl. Mech. Eng. 373 (2021), 113440 DOI: 10.1016/j.cma.2020.113440

Reese, S.; Brepols, T.; Fassin, M.; Poggenpohl, L.; Wulfinghoff, S.:
Using structural tensors for inelastic material modeling in the finite strain regime – A novel approach to anisotropic damage
Journal of the Mechanics and Physics of Solids 146 (2021) DOI: 10.1016/j.jmps.2020.104174

Eckert, S.:
Multi-Cycle Process Signature of Laser-Induced Thermochemical Polishing
Journal of Manufacturing and Materials Processing 3, 90 (2019) DOI: 10.3390/jmmp3040090

Gräbner, D.; Lang, W.:
In-situ sub-surface strain measurement in deep rolling processes
Proceedings of the IEEE Sensors Conference 2020 DOI: 10.1109/SENSORS47125.2020.9278944

Klink, A.; Rommes, B.; Heidemanns, L.; Herrig, T.:
Investigations of Single Pulse Smoothing Characteristics during PECM
Proceedings of the 16th International Symposium on Electrochemical Machining Technology INSECT, 24-25 November 2020, Chemnitz, Germany, pp. 35-40 ISBN: 978-3-95735-125-8

Rommes, B.; Klink, A.; Herrig, T.; Vorspohl, J.; Ehle, L.; Bergs, T.:
Formation of Flow-Grooves during Electrochemical Machining
Proceedings of the 16th International Symposium on Electrochemical Machining Technology INSECT, 24-25 November 2020, Chemnitz, Germany, 27-32 ISBN: 978-3-95735-125-8

Gierden, C.; Kochmann, J.; Waimann, J.; Kinner-Becker, T.; Sölter, J.; Svendsen, B.; Reese, S.:
Efficient two-scale FE-FFT-based mechanical process simulation of elasto-viscoplastic polycrystals at finite strains
Computer Methods in Applied Mechanics and Engineering 374 (2021), 113566 DOI: 10.1016/j.cma.2020.113566

Bergs, T.; Borrmann, J.P.; Schüler, M.; Herrig, T.; Döring, J.E.:
Pure waterjet controlled depth machining for stripping ceramic thermal barrier coatings on turbine blades
Procedia CIRP 85. 2019, 261–265 DOI: 10.1016/j.procir.2019.09.029

Bergs, T.; Schüler, M.; Arntz, K.; Herrig, T.:
Technological analysis of different abrasive water jet machining strategies for blisk roughing
WJTA Conference & Expo. 11.-13.11.2019, New Orleans

Kochmann, J.:
Efficient FE- and FFT-based two-scale methods for micro-heterogeneous media
Dissertation RWTH Aachen 2019 DOI: 10.18154/RWTH-2019-05432

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Induction of Highly Dynamic Shock Waves in Machining Processes with Multiple Loads and Short Tool Impacts
Applied Sciences 2019, 9(11), 2293 DOI: https://doi.org/10.3390/app9112293

Tausendfreund, A.; Alexe, A.; Stöbener, D.; Fischer, A.:
Messung mechanischer Beanspruchungen in laufenden Schleifprozessen.
VDI-Berichte, Band 2019, 20. GMA/ITG-Fachtagung Sensoren und Messsysteme ISBN: 978-3-9819376-0-2

Holsten, M.; Klink, A.; Bergs, T.:
Concepts for Advancing the Use of Process Data in Electrical Discharge Machining
Procedia CIRP 82 (2019), 220-223 DOI: 10.1016/j.procir.2019.03.279

Bergs, T.; Schneider, S.; Harst, S.; Klink, A.:
Numerical simulation and validation of material loadings during electrical discharge machining
Procedia CIRP 82 (2019), 14-19 DOI: 10.1016/j.procir.2019.04.165

Bergs, T.; Mohammadnejad, M.; Hess, R.; Harst, S.; Klink, A.:
Simulation of Thermal Induced Microstructure Evolution within the Heat Affected Zone
Procedia CIRP 82 (2019), 432-437 DOI: 10.1016/j.procir.2019.04.144

Wielki, N.; Kuschel, S.; Sölter, J.:
A Comparative Study of the Influence of the Strain-Hardening in Chip Formation Simulations using Different Software Packages
Proceedings 17th CIRP Conference on Modelling of Machining Operations (CMMO), 13-14 June 2019, Sheffield, UK, Procedia CIRP 82 (2019) pp. 43-46 https://doi.org/10.1016/j.procir.2019.03.275

Meyer, H.; Epp. J; Zoch, H.-W.; Pirling, T.:
Measuring internal load during metal processing
ILL Annual Report 2018, pp. 53-53 DOI: 10.1520/MPC20170132

Kunieda, M.; Overmeyer, L.; Klink, A.:
Visualization of electro-physical and chemical machining processes
CIRP Annals Volume 68 (2019) 2, 751-774 DOI: 10.1016/j.cirp.2019.05.011

Zander, D.; Klink, A.; Harst, S.; Klocke, F.; Altenbach, C.:
Influence of machining processes on rim zone properties and high temperature oxidation behavior of 42CrMo4
Materials and Corrosion 70 (2019) 12, 2190-2204 DOI: 10.1002/maco.201910928

Klink, A.; Rommes, B.; Zander, D.; Schupp, A.; Vollertsen, F.; Eckert, S.:
Mechanism-based classification of electrochemical machining processes
Proceedings of the 15th International Symposium on Electrochemical Machining Technology INSECT, 14-15 November 2019, Saarbrücken, Germany, 166-171 ISBN: 978-3-00-064086-5

Cavaliere, F.; Reese, S.; Wulfinghoff, S.:
Efficient two-scale simulations of engineering structures using the Hashin-Shtrikman type Finite Element method
Computational Mechanics 65 (2020), 159-175 DOI: 10.1007/s00466-019-01758-4

Jaworek, D.; Gierden, C.; Waimann, J.; Wulfinghoff, S.; Reese, S.:
A Hashin-Shtrikman type semi-analytical homogenization procedure
Proceedings in Applied Mathematics and Mechanics 19 (1) (2019), e201900191 DOI: 10.1002/pamm.201900191

Gierden, C.; Kochmann, J.; Manjunatha, K.; Waimann, J.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
A model order reduction method for finite strain FFT solvers using a compressed sensing technique
Proceedings in Applied Mathematics and Mechanics; Wiley; Vol 19 (1); 2019; DOI: 10.1002/pamm.201900037

Rezaei, S.; Jaworek, D.; Rezaei Mianroodi, J.; Wulfinghoff, S.; Reese, S.:
Atomistically motivated interface model to account for coupled plasticity and damage at grain boundaries
Journal of the Mechanics and Physics of Solids 124 (2018), 325-349 DOI: 10.1016/j.jmps.2018.10.015

Gierden, C.; Kochmann, J.; Waimann, J.; Svendsen, B.; Reese, S.:
Microstructural convergence analysis as basis for an efficient and accurate two-scale FE-FFT-based simulation approach
Proceedings of the 8th GACM Colloquium on Computational Mechanics for Young Scientists from Academia and Industry; 2019;GACM, Kassel (Germany), August 28-30, 2019 ISBN: 978-3-86219-5093-9

Harst, S.:
Entwicklung einer Prozesssignatur für die elektrochemische Metallbearbeitung
Dissertation RWTH Aachen 2019; Apprimus Verlag ISBN: 978-3-86359-750-4

Bergs, T.; Rommes, B.; Harst, S.; Herrig, T.; Klink, A.:
Influence of initial geometric deviations on the shaping accuracy during electrochemical machining
15th International Symposium on Electrochemical Machining Technology Insect 2019 Proceedings ISBN: 978-3-00-064086-5

Eckert, S.:
Multi Cycle Process Signature of Laser Induced Thermochemical Polishing
Journal of Manufacturing and Materials Processing 3 (2019) DOI: 10.3390/jmmp3040090

Brinksmeier, E.; Reese, S.; Sölter, J.:
The Right Signature for Every Process
german research (2019) 2, 26-29 DOI: 10.1002/germ.201970208

Klink, A.:
Paradigm Shifts in ECM and EDM Process Technology Design Approaches
69th CIRP General Assembly, 18.-24.08.2019, Birmingham, England

Klink, A.:
Modellgestützte Einstellung von Randzoneneigenschaften für elektroerosive Fertigungsprozesse
Werkstoffwoche 2019 – Symposium Surface Engineering durch Fertigungsprozesse, 18.-20.09.2019, Dresden, Germany

Sölter, J.:
Prozesssignaturen - Ein neuartiger Ansatz zur gezielten Einstellung von Randzoneneigenschaften in der Fertigung
Werkstoffwoche 2019 – Symposium Surface Engineering durch Fertigungsprozesse, 18.-20.09.2019, Dresden, Germany

Willert, M.:
Mikrogeometrische Einflüsse bei der Präzisionsbearbeitung von Stahl
Dissertation Bremen, (2019)

Burkart, K.; Clausen, B.; Zoch, H.-W.:
Evaluation of multiple-flaw failure of bearing steel 52100 of different heats in the VHCF regime and mathematical determination of single-flaw behavior
Fatigue of Materials at Very High Numbers of Loading Cycles, Christ, H.J. (Hrsg.), 1. Auflage, Springer Spektrum, Wiesbaden, 2018, S. 211-232 DOI: 10.1007/978-3-658-24531-3_10

Lange, A.; Abraham, S.; Fechte-Heinen, R.; Winzer, N. A.; Kern, A.:
Processing and mechanical properties of highly formable ferritic high strength steel containing titanium nano carbides for automotive applications
Mat. Sci. For. 941 (2018), 382–385 DOI: 10.4028/www.scientific.net/MSF.941.382

Schumacher, J.; Clausen, B.; Zoch, H.-W.:
Influence of inclusion type and size on the fatigue strength of high strength steels
MATEC Web of Conferences 165, 14003 (2018) DOI: 10.1051/matecconf/201816514003

Kochmann, J.; Wulfinghoff, S.; Ehle, L.; Mayer, J.; Svendsen, B.; Reese, S.:
Efficient and accurate two-scale FE-FFT-based prediction of the effective material behavior of elasto-viscoplastic polycrystals
Computational Mechanics 61 (2018), 751-764 DOI: 10.1007/s00466-017-1476-2

Tausendfreund, A.; Stöbener, D.; Fischer, A.:
Precise In-Process Strain Measurements for the Investigation of Surface Modification Mechanisms
Journal of Manufacturing and Materials Processing, 2018, 2(1), 9, DOI: https://doi.org/10.3390/jmmp2010009

Kolkwitz, B.; Kohls, E.; Heinzel, C.; Brinksmeier, E.:
Correlations between Thermal Loads during Grind-Hardening and Material Modifications Using the Concept of Process Signatures
Journal of Manufacturing and Materials Processing 20 (2018) 2 DOI: 10.3390/jmmp2010020

Klocke, F.; Schneider, S.; Frauenknecht, B.; Hensgen, L.; Klink, A.; Oßwald, K.:
Thermographic Analysis of Spark Location Distribution in Sinking EDM
Procedia CIRP 68 (2018), 280-285 DOI: 10.1016/j.procir.2017.12.064

Willert, M.; Riemer, O.; Karpuschewski, B.:
Analysis of mechanical impact in precision cutting processes
Proceedings of the 18th international conference of the european society for precision engineering and nanotechnology, June 4th – 8th June 2018, Venice, Italy, pp. 359-360 ISBN: 978-0-9957751-2-1

Brinksmeier, E.; Meyer, D.; Heinzel, C.; Lübben, T.; Sölter, J.; Langenhorst, L.; Frerichs, F.; Kämmler, J.; Kohls, E.; Kuschel, S.:
Process Signatures - The Missing Link to Predict Surface Integrity in Machining
Procedia CIRP 71 (2018), 3-10 DOI: 10.1016/j.procir.2018.05.006

Kämmler, J.; Borchers, F.; Meyer, D.; Heinzel, C.:
Material removal mechanisms and deformation analysis by flycutting tests with round and polygon shaped tools on AISI4140 steel
Euspen ICE, Conference Proceedings 2018, 341-342 ISBN: 978-0-9957751-2-1

Kämmler, J.; Wielki, N.; Meyer, D.:
Surface integrity after internal load oriented multistage contact deep rolling
Procedia CIRP 71 (2018), 490-495 DOI: 10.1016/j.procir.2018.05.026

Borchers, F.; Kämmler, J.; Meyer, H.; Epp, J.; Meyer, D.:
Influence of pre-machining on the surface integrity after processing by mechanical surface treatment
Procedia CIRP 71 (2018), 453-459 DOI: 10.10116/j.procir.2018.05.047

Hoffmann, F.; Kleff, J.; Strunk, R.; Clausen, B.:
Influence of process chains on heat treatment
Materialwissenschaft und Werkstofftechnik 2018,Volume 49, Issue 6, pp. 792-802

Willert, M.; Rickens, K.; Riemer, O.:
Surface integrity in ultrasonic assisted diamond cutting of steel
Proceedings of the 6th International Conference on nanoManufacturing, nanoMan2018, 4 - 6 July 2018, Brunel University London

Gräbner, D.; Dumstorff, G.; Lang, W.:
Simultaneous Measurement of Strain and Temperature with two Resistive Strain Gauges made from Different Materials
Procedia Manufacturing 24 (2018), 258-263 DOI: 10.1016/j.promfg.2018.06.030

Kochmann, J.; Ehle, L.; Wulfinghoff, S.; Mayer, J.; Svendsen, B.; Reese, S.:
Efficient Multiscale FE-FFT-based Modeling and Simulation of Macroscopic Deformation Processes with Non-linear Heterogeneous Microstructures
Multiscale Modeling of Heterogeneous Structures 86 (2018), 129-146 DOI: 10.1007/978-3-319-65463-8_7

Ehle, L.; Kohls, E.; Richter, S.; Spille, J.; Schwedt, A.; Mayer, J.:
Grind hardening: Correlations between surface modifications and applied internal loads
Procedia CIRP 71 (2018), 341-347 DOI: 10.1016/j.procir.2018.05.038

Frerichs, F.; Lübben, T.:
Development of Process Signatures for Manufacturing Processes with Thermal Loads without and with hardening
Procedia CIRP 71 (2018), 418-423 DOI: 10.1016/j.procir.2018.05.057

Frerichs, F.; Meyer, H.; Strunk, R.; Kolkwitz, B.; Epp, J.:
Development of a Process Signature for Manufacturing Processes with Thermal Loads
Metallurgical and Materials Transactions A 49 (2018) 8, 3419–3429 DOI: 10.1007/s11661-018-4719-8

Klocke, F.; Harst, S.; Zeis, M.; Klink, A.:
Modeling and Simulation of the Microstructure Evolution of 42CrMo4 Steel during Electrochemical Machining
Procedia CIRP 68 (2018), 505-510 DOI: 10.1016/j.procir.2017.12.082

Klocke, F.; Mohammadnejad, M.; Holsten, M.; Ehle, L.; Zeis, M.; Klink, A.:
A comparative study of polarity-related effects in single discharge EDM of titanium and iron alloys
Procedia CIRP 68 (2018), 52-57 DOI: 10.1016/j.procir.2017.12.021

Klocke, F.; Mohammadnejad, M.; Zeis, M.; Klink, A.:
Investigation on the Variability of Existing Models for Simulation of Local Temperature Field during a Single Discharge for Electrical Discharge Machining (EDM)
Procedia CIRP 68 (2018), 260-265 DOI: 10.1016/j.procir.2017.12.059

Eckert, S.; Vollertsen, F.:
Mechanisms and processing limits of surface finish using laser-thermochemical polishing
CIRP Annals – Manufacturing Technology 67 (2018) 1, 201-204 DOI: 10.1016/j.cirp.2018.04.098

Klocke, F.; Mohammadnejad, M.; Hess, R.; Harst, S.; Klink, A.:
Phase Field Modeling of the Microstructure Evolution in a Steel Workpiece under High Temperature Gradients
Procedia CIRP 71 (2018), 99-104 DOI: 10.1016/j.procir.2018.05.079

Meyer, H.; Epp, J.; Pirling, T.; Zoch, H.-W.:
In Situ Investigations of Elastic Strain State in Deep Rolled 4140H Steel by Neutron Diffraction Method
Materials Performance and Characterization, Vol. 7, No. 4, 2018 http://dx.doi.org/10.1520/MPC20170132

Meyer, H.; Epp, J.; Zoch, H.-W.:
Residual stress and dislocation density development in single track deep rolled AISI 4140H steel
Procedia CIRP 71 (2018), 192-197 DOI: 10.1016/j.procir.2018.05.096

Meyer, H.; Epp, J.:
In-Situ Analysis of Material Modifications During Deep Rolling by Synchrotron X-Ray Diffraction Experiments
Materials Research Proceedings, Vol. 6 (2018), pp 27-32 European Conference on Residual Stresses - ECRS10 in Leuven, Belgium, on 11-14 September, 2018. DOI: http://dx.doi.org/10.21741/9781945291890-5

Brinksmeier, E.; Reese, S.; Klink, A.; Langenhorst, L.; Lübben, T.; Meinke, M.; Meyer, D.; Riemer, O.; Sölter, J.:
Underlying Mechanisms for Developing Process Signatures in Manufacturing
Nanomanufacturing and Metrology 1 (2018) 4, 193-208 DOI: 10.1007/s41871-018-0021-z

Langenhorst, L.; Borchers, F.; Heinzel, C.:
Analysis of internal material loads and resulting modifications for grinding with mechanical main impact
Procedia CIRP 77 (2018), 533-536 DOI: 10.1016/j.procir.2018.08.241

Tausendfreund, A.; Borchers, F.; Kohls, E.; Kuschel, S.; Stöbener, D.; Heinzel, C.; Fischer A.:
Investigations on Material Loads during Grinding by Speckle Photography
Journal of Manufacturing and Materials Processing 71 (2018) 2 DOI: 10.3390/jmmp2040071

Tausendfreund, A.; Alexe, G.; Stöbener, D.; Fischer, A.:
Application limits of digital speckle photography for in-process measurements in manufacturing processes
The European Optical Society Biennial Meeting 2018, 8-12 Oct. Delft, Netherlands pp. 255-256 ISBN: 978-952-68553-7-0

Meyer, H; Epp, J.:
In Situ X-ray Diffraction Analysis of Stresses during Deep Rolling of Steel
Quantum Beam Science 2018, 2(4), 20 DOI: http://dx.doi.org/10.3390/qubs2040020

Eckert, S.; Brito Gadeschi, G.; Meinke, M.; Vollertsen, F.; Schröder, W.:
Comparison of laser induced thermal heat impact on 42CrMo4 in gaseous and liquid ambient
Proceedings of the 14th International Symposium on Electrochemical Machining Technology INSECT (2018), Aachen, Germany ISBN: 978-3863596675

Kochmann, J.; Manjunatha, K.; Gierden, C.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
A simple and flexible model order reduction method for FFT-based homogenization problems using a sparse sampling technique
Computer Methods in Applied Mechanics and Engineering 347 (2019), 622-638 DOI: 10.1016/j.cma.2018.11.032

Brinksmeier, E.; Reese S. ; Sölter, J.:
Für jeden Prozess die passende Signatur
Forschung – Das Magazin der Deutschen Forschungsgemeinschaft 43 (2018) 3, 20-23 DOI: 10.1002/fors.201870307

Meyer, D.; Kämmler, J.:
Sustainable approach of heat treatment-free surface hardening by deep rolling
International Journal of Sustainable Manufacturing, Vol. 4, Issue 1, 2018, pp. 64-78

Zhao, T.; Eckert, S.; Vollertsen, F.:
Recast Zone and Unmelted Zone of the White Layer Induced by Microsecond Pulsed Laser Surface Processing of 42CrMo4 Alloy steel
Lasers in Engineering (Old City Publishing) (2018), Vol. 41 Issue 4-6, pp. 349-358 ISSN: 0898-1507

Kochmann, J.; Brepols, T.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
On the computation of the exact overall consistent algorithmic tangent moduli for non-linear finite strain homogenization problems using six finite
Proceedings of the 6th European Conference on Computational Mechanics (ECCM6) and 7th European Conference on Computational Fluid Dynamics (ECFD7); ECCM6 and ECFD7, Glasgow (UK), June 11-15, 2018 ISBN: 978-84-947311-6-7

Kochmann, J.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
Numerically robust two-scale full-field finite strain crystal plasticity simulations of polycrystalline materials
Proceedings in Applied Mathematics and Mechanics; Wiley; Vol. 18 (1); 2018 ISSN: 1617-7061

Kochmann, J.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
Efficient and accurate two-scale simulation of non-linear heterogeneous microstructures
Proceedings in Applied Mathematics and Mechanics; Wiley; Vol. 17 (1); 2018; S. 803-804 DOI: 10.1002/pamm.201710369

Wulfinghoff, S.; Cavaliere, F.; Reese, S.:
Model-order reduction of nonlinear homogenization problems using a Hashin-Shtrikman type finite element method
Computer Methods in Applied Mechanics and Engineering 330 (2018), 149-179 DOI: 10.1016/j.cma.2017.10.019

Meyer, H.:
Measuring internal material load during metal processing
ILL annual report (2018), 52-53

Aretz, A.; Ehle, L.; Haeusler, A.; Bobzin, K.; Öte, M.; Wiesner, S.; Schmidt, A.; Gillner, A.; Poprawe, R.; Mayer, J.:
In situ investigation of production processes in a large chamber scanning electron microscope
Ultramicroscopy 193 (2018), 151-158 DOI: 10.1016/j.ultramic.2018.07.002

Strunk, R.; Borchers, F.; Clausen, B.; Heinzel, C.:
Influence of mechanical and thermal loads on defined surface modifications
MSE 2018, Darmstadt

Strunk, R.; Clausen, B.; Zoch, H.-W.:
Structural changes in the surface of deep rolled samples due to thermal loads
International Journal of Engineering Research and Applications (IJERA) 7 (2017) 1, pp. 86-94 ISSN: 2248-9622; Doi:10.9790/9622-0701048694

Hoffmann, F.; Clausen, B.; Kleff, J.:
Prozessketteneinflüsse auf die Wärmebehandlung
Journal of Heat Treatment and Materials HTM 72 (2017) 1, pp. 50-61

Harder, I.; Walter, C.; Brinksmeier, E.:
Engaging the Public in Engineering Science – Successful Measures for a Public Dialog
http://www.sciencedirect.com/science/article/pii/S2351978917300161/pdf?md5=eea91c4bb64baa41f0139666594c767e&pid=1-s2.0-S2351978917300161-main.pdf

Clausen, B.; Strunk, R.; Zoch, H.-W.:
A Short Review Concerning the Basic Mechanisms of Surface Modifications due to Machining Operations
Int J Metall Met Phys , IJMMP-2-004, (Volume 2, Issue 1) http://vibgyorpublishers.org/content/international-journal-of-metallurgy-and-metal-physics/ijmmp-2-004.php

Dumstorff, G.; Lang, W.; Riemer, O.; Willert, M.:
Characterizing precision cutting process by workpiece integrated printed thermocouples
Proceedings of the 17th international conference of the european society for precision engineering and nanotechnology, May 29th – 2nd June 2017, Hannover, Germany

Rickens, K.; Riemer, O.; Willer, M.; Wolf, A.:
Study on the critical chip thickness in microcutting SiC single crystals
Proceedings of the 17th international conference of the european society for precision engineering and nanotechnology, May 29th – 2nd June 2017, Hannover, Germany

Borchers, F.; Heinzel, C.; Lang, W.; Sarma, M.:
In situ strain measurement during a grinding process using a sensor-integrated workpiece
Proceedings of the 17th international conference of the european society for precision engineering and nanotechnology, May 29th – 2nd June 2017, Hannover, Germany. pp. 363-364

Klocke, F.; Harst, S.; Ehle, L.; Zeis, M.; Klink, A.:
Surface integrity in electrochemical machining processes: An analysis on material modifications occurring during electrochemical machining
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture https://doi.org/10.1177/0954405417703422

Klocke, F.; Harst, S.; Karges, F.; Zeis, M.; Klink, A.:
Modeling of the Electrochemical Dissolution Process for a Two-phase Material in a Passivating Electrolyte System
16th CIRP Conference on Modeling of Machining Operations (CMMO), Procedia CIRP 58 (2017) pp. 169 – 174 https://doi.org/10.1016/j.procir.2017.03.214

Brito Gadeschi, G.; Schneider, S.; Mohammadnejad, M.; Meinke, M.; Klink, A.; Schöder, W.; Klocke, F.:
Numerical Analysis of Flushing-Induced Thermal Cooling Including Debris Transport in Electrical Discharge Machining (EDM)
16th CIRP Conference on Modeling of Machining Operations (CMMO), Procedia CIRP 58 (2017) pp. 116 – 121 https://doi.org/10.1016/j.procir.2017.03.325

Klocke, F.; Schneider, S.; Mohammadnejad, M.; Hensgen, L.; Klink, A.:
Inverse Simulation of Heat Source in Electrical Discharge Machining (EDM)
16th CIRP Conference on Modeling of Machining Operations (CMMO), Procedia CIRP 58 (2017) pp. 1-6 https://doi.org/10.1016/j.procir.2017.03.178

Oßwald, K.; Schneider, S.; Hensgen, L.; Klink, A.; Klocke, F.:
Experimental Investigation of Energy Distribution in Continuous Sinking EDM
CIRP Journal of Manufacturing Science and Technology Volume 19, November 2017, Pages 36-43 DOI: 10.1016/j.cirpj.2017.04.006

Rezaei, S.; Kochmann, J.; Wulfinghoff, S.; Reese, S.:
Cohesize zone-based modeling of nano-coating layers for the purpose of establishing process signatures
Aktzeptiert, Review bereits gespeichert, Meldung nochmal senden

Klaproth, F.; Vollertsen, F.:
Laserstrukturen für definierte Kontakteigenschaften
Mikroproduktion, 2 (2017), S. 46-49

Zhao, T.; Vollertsen, F.:
Process Signatures as a Measure for Loopless Production
Engineering, 9 (2017) pp. 328-337

Buchkremer, S.:
Irreversible Thermodynamics of Nano-Structural Surface Modifications in Metal Cutting
Apprimus Verlag, Aachen, 2017 ISBN: 978 – 3 3 86359 – 508 - 1

Buchkremer, S.; Klocke, F.:
Compilation of a thermodynamics based process signature for the formation of residual surface stresses in metal cutting
Wear 376-377 Part B (2017), pp. 1156-1163 DOI: 10.1016/j.wear.2016.11.013

Buchkremer, S.; Klocke, F.; Döbbeler, B.; Abouridouane, M.; Meurer, M.:
Thermodynamics-Based Interpretation of White Layer Formation in Metal Cutting
16th CIRP Conference on Modeling of Machining Operations, Procedia CIRP 58 (2017), pp. 370-374 DOI: 10.1016/j.procir.2017.03.328

Buchkremer, S.; Klocke, F.:
Modeling nanostructural surface modifications in metal cutting by an approach of thermodynamic irreversibility: Derivation and experimental validation
Journal of Continuum Mechanics and Thermodynamics 29 (2017) 1, pp. 271-289 DOI: 10.1007/s00161-016-0533-y

Willert, M.; Riemer, O.; Brinksmeier, E.:
Surface integrity in precision turning of steel
Int J Adv Manuf Technol 94 (2018), 763-771 DOI: 10.1007/s00170-017-0696-0

Heinzel, C.; Sölter, J; .Gulpak, M.; Riemer, O.:
An analytical multilayer source stress approach for the modelling of material modifications in machining
CIRP Annals – Manufacturing Technology 66 (2017) 1, pp. 531-534 ISSN: 0007-8506, DOI: 10.1016/j.cirp.2017.04.073

Langenhorst, L.; Gulpak, M.; Sölter, J.; Riemer, O.:
Effects of model reduction on simulated temperature fields in milling
Proceedings 16th CIRP Conference on Modelling of Machining Operations (CMMO), 15-16 June 2017, Cluny, France, Procedia CIRP 58 (2017), pp. 511-516 ISSN: 2212-8271, DOI: 10.1016/j.procir.2017.03.260

Brito Gadeschi, G.; Schneider, L.; Meinke, M.; Schöder, W.:
Direct particle-fuid simulation of flushing in die-sink electrical-discharge machining
AIAA 2017-3619, 23rd AIAA Computational Fluid Dynamics Conference, AIAA AVIATION 2017, Denver, Colorado, USA. DOI: https://doi.org/10.2514/6.2017-3619

Sarma, M.; Borchers, F.; Dumstorff, G.; Heinel, C.; Lang, W.:
Measuring strain during a cylindrical grinding process using embedded sensors in a workpiece
Journal of Sensor and Sensor Systems, 6 (2017) pp. 331-340

Reimers, M.; Lang, W.; Dumstorff, G.:
Experimental and Numerical Investigations in Shallow Cut Grinding by Workpiece Integrated Infrared Thermopile Array
MDPI Sensors Journal 10 (2017) DOI: 10.3390/s17102250

Zeis, M.:
Verformung dünnwandiger Graphitelektroden mit hohen Aspektverhältnissen beim funkenerosiven Senken
Dissertation ISBN:978-3-86359-536-4

Zeis, M.:
Deformation of thin graphite electrodes with high aspect ratio during sinking electrical discharge machining
CIRP Annals – Manufacturing Technology 66 (2017) 1, 185-188 DOI: 10.1016/j.cirp.2017.04.139

Klocke, F.; Zeis, M.; Heidemanns, L.:
Fluid structure interaction of thin graphite electrodes during flushing movements in sinking electrical discharge machining
CIRP Journal of Manufacturing Science and Technology DOI: https://doi.org/10.1016/j.cirpj.2017.09.003

Wulfinghoff, S.:
A generalized cohesive zone model and a grain boundary yield criterion for gradient plasticity derived from surface-and interface-related arguments
International Journal of Plasticity; Elsevier; Vol. 92; 2017; S. 57-78 DOI: 10.1016/j.ijplas.2017.02.006

Felder, S.; Kochmann, J.; Wulfinghoff, S.; Reese, S.:
Multiscale FE-FFT-based thermo-mechanically coupled modeling of viscoplastic polycrystalline materials
Proceedings of the 7th GACM Colloquium on Computational Mechanics for Young Scientists from Academia and Industry; 2017; S. 799-802

Brinksmeier, E.:
Generation of Predictable Surface Integrity State of Machined Components
Numerically robust two-scale full-field finite strain crystal plasticity simulations of polycrystalline materials

Klocke, F.; Harst, S.; Zeis, M.; Klink, A.:
Energetic Analysis of the Anodic Double Layer during Electrochemical Machining of 42CrMo4 Steel
18th CIRP Conference on Electro Physical and Chemical Machining (ISEM XVIII)

Klocke, F.; Mohammadnejad, M.; Zeis, M.; Klink, A.:
Potentials of the Phase Field Approach for Modeling Modifications in Material Microstructure during Electrical Discharge Machining
Proceedings of the 18th CIRP Conference on Electro Physical and Chemical Machining (ISEM XVIII) 2016, 18-22 April 2016, Tokyo, Japan, Procedia CIRP 42 (2016), pp. 396 – 401

Klocke, F.; Schneider, S.; Ehle, L.; Meyer, H.; Hensgen, L.; Klink, A.:
Investigations on Surface Integrity of Heat Treated 42CrMo4 (AISI 4140) Processed by Sinking EDM
Procedia CIRP, Volume 42, 2016, pp. 580-585

Klocke, F.; Ehle, L.; Hensgen, L.; Klink, A.; Schwedt, A.:
Structure and Composition of the White Layer in the Wire-EDM Process
Procedia CIRP, Volume 42, 2016, pp. 673-678

Klink, A.:
Process Signatures of EDM and ECM Processes – Overview from Part Functionality and Surface Modification Point of View
Procedia CIRP 42 2016, 240-245 DOI: 10.1016/j.procir.2016.02.279

Dumstorffa, G.; Sarma, M.; Reimers, M.; Kolkwitz, B.; Brinksmeier, E.; Heinzel, C.; Lang, W.:
Steel integrated thin film sensors for characterizing grinding processes
Sensors and Actuators A: Physical

Kochmann, J.; Wulfinghoff, S.; Reese, S.; Rezai Mianroodi, J.; Svendsen, B.:
Two-scale FE-FFT- and phase-field-based computational modeling of bulk microstructural evolution and macroscopic material behavior
Computer Methods in Applied Mechanics and Engineering 305 (2016), 89-110 DOI: 10.1016/j.cma.2016.03.001

Brito Gadeschi, G.; Meinke, M.; Schröder, W.:
A hierarchical Cartesian method for conjugate heat transfer involving moving bodies
AIAA 2016-0606, 54th AIAA Aerospace Sciences Meeting, AIAA SciTech 2016, San Diego, California, USA.

S. Gladkov, J. Kochmann, M. Hütter, S. Reese, B. Svendsen:
Thermodynamic Model Formulations for Inhomogeneous Solids with Application to Non-isothermal Phase Field Modelling
Journal of Non-Equilibrium Thermodynamics, 41 (2) pp. 131-139, 2016, DOI: 10.1515/jnet-2015-0062

Willert, M.; Riemer, O.; Brinksmeier, E.:
Size effect in micro machining of steel depending on the material state
Proceedings of the 7th CIRP Conference on High Performance Cutting (HPC), Chemnitz, Germany, 31.05.-02.06.2016, Procedia CIRP 46 (2016), pp. 193-196

Sari, D.; Welling, D.; Löpenhaus, C.; Klocke, F.; Klink, A.:
Adjusting surface integrity of gears using wire EDM to increase the flank load carrying capacity
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 293-298

Ehle, L.; Kämmler, J.; Meyer, D.; Schwedt, A.; Mayer, J.:
Electron Microscopic Characterization of Mechanically Modified Surface Layers of Deep Rolled Steel
Procedia CIRP 45 (2016), 367-370 DOI: 10.1016/j.procir.2016.02.147

Kuschel, S.; Kolkwitz, B.; Sölter, J.; Brinksmeier, E.; Heinzel, C.:
Experimental and Numerical Analysis of Residual Stress Change Caused by Thermal Loads During Grinding
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 51-54

Frerichs, F.; Sölter, J.; Lübben, T.; Brinksmeier, E.; Zoch, H.:
A Simulation Based Development of Process Signatures for Manufacturing Processes with Thermal Loads
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 327-330

Mehrafsun, S.; Harst, S.; Hauser, O.; Eckert, S.; Klink, A.; Klocke, F.; Vollertsen, F.:
Energy-based Analysis of Material Dissolution Behavior for Laser-Chemical and Electrochemical Machining
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 347-350

Jermolajev, S.; Epp, J.; Heinzel, C.; Brinksmeier, E.:
Material modifications caused by thermal and mechanical load during grinding
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 43-46

Klocke, F.; Döbbeler, B.; Buchkremer, S.:
On the Applicability of the Concept of Process Signatures to Hard Turning
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 7-10

Abouridouane, M.; Klocke, F.; Döbbeler, B.:
Analytical temperature prediction for cutting steel
Procedia CIRP, Volume 65(1), 2016, pp. 77-80

Riemer, O.; Willert, M.; Wolf, A.:
Correlation of process loads and surface integrity in precision cutting
5th International Conference on Nanomanufacturing, 15. – 17.08.2016 Macau, China. Conference Proceedings

Borchers, F.; Wagner, A.; Heinzel, C. Prof.; Meyer, D:
Schleifen mit elastischen Werkzeugen
Werkstattstechnik online 106 (2016), 380-386

Heinzel, C.; Borchers, F.; Berger, D.; Ehle, L.:
Surface and material modifications of tempered steel after precision grinding with electroplated coarse grained diamond wheels
Proceedings of the 3rd CIRP Conference on Surface Integrity (CSI), Charlotte, USA, 08.06.-10.06.2016, Procedia CIRP 45 (2016), pp. 191-194

Meyer, D.; Kämmler, J.:
Surface integrity of AISI 4140 after deep rolling with varied external and internal loads
Procedia CIRP 45 (2016), 363-366 DOI: 10.1016/j.procir.06.0.356

Buchkremer, S.; Klocke, F.; Döbbeler, B.:
Impact of the Heat Treatment Condition of Steel AISI 4140 on Its Frictional Contact Behavior in Dry Metal Cutting
Journal of Manufacturing Science and Engineering. Vol. 138, No. 12

Gladkov, S.;Kochmann, J.; Reese, S.; Hütter, M.; Svendsen, B.:
Thermodynamic Model Formulations for Inhomogeneous Solids with Application to Non-isothermal Phase Field Modelling
Journal of Non-Equilibrium Thermodynamics, 41 (2): pp. 131-139, 2016. DOI: 10.1515/jnet-2015-0062

Klink, A.; Mattfeld, P.; Augspurger, T.; Schneider, S.:
Energieflüsse in der Fertigung besser verstehen
RWTH Themen Forschungsmagazin 01/2016: pp. 36-39

Kochmann, J.; Ehle, L.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
Linking macroscopic deformation processes to microstructure evolution using an FE-FFT-based micro-macro transition and non-conserved phase-fields
Proceedings in Applied Mathematics and Mechanics, 16, pp. 535-536. doi: 10.1002/pamm.201610256

Wulfinghoff, S.; Alipour, A.; Rezaei, S.; Kochmann, J.; Reese, S.:
Generalized Interface Models With Damage in Gradient Plasticity
Proceedings in Applied Mathematics and Mechanics, 16, pp. 411-412. doi: 10.1002/pamm.201610194

Klocke, F.; Vollertsen, F.; Harst, S.; Eckert, S.; Zeis, M.; Klink, A.; Mehrafsun, S.:
Comparison of Material Modifications occuring in Laserchemical and Electrochemical Machining
Proceedings of the 12th INSECT 2016, Brüssel, Belgien, 17.11-18.11.2016, pp. 57-63, ISBN: 978-9-4619746-1-7

Zhao, T.; Mehrafsun, S.; Vollertsen, F.:
Energy-based approach as an example for a process signature for laser microprocessing
SPIE/COS Photonics Asia 2016, Beijing, China, 12.10-14.10.2016, DOI:10.1117/12.2245445

Reimers, S.; Kolkwitz, B.; Beck, D.; Sarma, M.; Heinzel, C.; Lang, W.; Dumstorff, G.:
Steel Integrated IR Thermopile Array for Characterizing Grinding Processes
30th Eurosensors 2016, Budapest, Ungarn, 04.09-07.09.2016, pp. 1568-1572 DOI: 10.1016/j.proeng.2016.11.462

Dumstorff, G.:
Modellierung und experimentelle Untersuchung von materialintegrierten Sensoren
Dissertation, Dr. Hut Verlag ISBN: 978-3-8439-2588-4

Klink A.; Holsten M.; Schneider S.; Koshy P.:
Acoustic emission signatures of electrical discharge machining
CIRP Annals - Manufacturing Technology, Vol. 65, 2016, pp. 229-232; ISSN: 0007-8506, DOI: http://dx.doi.org/10.1016/j.cirp.2016.04.082

Clausen, B.; Strunk, R.; Zoch, H.-W.:
The dependence of thermal and mechanical stability of residual stresses on their mode of generation
HTM J. Heat Treatm. Mat. 71 (2016) Vol. 6, pp. 251-257

Frerichs, F.; Lübben, T.; Zoch, H-W.:
Rekonstruktion von Eigenspannungstiefenverläufen aus Messungen von Maß- und Formänderungen und oberflächennahen Eigenspannungen
HTM J. Heat Treatm. Mat. 71 (2016) Vol. 6, pp. 241-250 DOI:10.3139/105.110306

Meyer, H.; Epp,J.; Zoch, H-W.:
In situ X-Ray Diffraction Investigation of Surface Modifications in a Deep Rolling Process under Static Condition
ICRS 10 - The 10th International Conference on Residual Stresses, Juli 3-7, 2016. Sydney, Australia

Epp, J.; Meyer, H.; Pirling, T.:
In situ measurement of surface modification mechanisms in the deep rolling process
Institut Laue-Langevin (ILL), Grenoble, France, Experimental report 12/2015 DOI: http://dx.doi.org/10.5291/ILL-DATA.1-02-179

Tausendfreund, A.; Stöbener, D.; Ströbel, G.:
In-process measurements of strain fields during grinding
Proceedings of the 16. international conference of the european society for precision engineering and nanotechnology (euspen), Nottingham, 30.05.-03.06.2016 ISBN 14: 978-0-9566790-8-6

Tausendfreund, A.; Stöbener, D.; Patzelt, S.; Ströbel, G.; Fischer, A.:
In-Prozess-Verformungsmessung auf Basis von Speckle-Korrelationsverfahren
In: Zimmermann, S. (Hrsg.): XXX. Messtechnisches Symposium des Arbeitskreises der Hochschullehrer für Messtechnik e. V. (AHMT), Hannover. De Gruyter, Oldenbourg, 2016, S. 201-207.

Epp, J.:
Effects of hydrostatic 2nd kind residual stresses and of carbon partitioning during martensitic quenching of low alloy steel
ICRS 10 - The 10th International Conference on Residual Stresses, Juli 3-7, 2016. Sydney, Australia ISBN: 978-1-94529116-6, DOI: http://dx.doi.org/10.21741/9781945291173-48

Epp, J.:
Time resolved investigations of phase transformations and stresses during heat treatment of steel samples by means of diffraction experiments
Dissertation, Shaker Verlag, ISBN: 978-3-8440-4547-5, DOI: http://dx.doi.org/10.2370/9783844045475

Schneiders, L.; Günther, C.; Meinke, M.M Schröder, W.:
An efficient conservative cut-cell method for rigid bodies interacting with viscous compressible flows
Journal of Computational Physics, Vol. 311, pages 62–86. DOI: https://doi.org/10.1016/j.jcp.2016.01.026

Schlimpert, S.; Meinke, M.; Schröder, W.:
Nonlinear analysis of an acoustically excited laminar premixed flame
Combustion and Flame, Vol. 163, pages 337–357. DOI: https://doi.org/10.1016/j.combustflame.2015.09.035

Radermacher A.; Reese S.:
POD-based model reduction with empirical interpolation applied to nonlinear elasticity
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING Int. J. Numer. Meth. Engng (2016) Vol. 107, 477–495. Published online 15 December 2015 in Wiley Online Library. DOI: 10.1002/nme.5177

Radermacher A.; Bednarcyk, B.; Stier, B.; Simon, J.; Zhou, L.; Reese S.:
Displacement-based multiscale modeling of fiber-reinforced composites by means of proper orthogonal decomposition
Adv.Model. and Simul. in Eng, SpringerOpen DOI: 10.1186/s40323-016-0082-8

Meyer, D.; Wagner, A.:
Influence of metalworking fluid additives on the thermal conditions in grinding
CIRP Annals - Manufacturing Technology 65 (2016) 313–316

Dumstorff, G.; Lang, W.:
Investigations on the Impact of Material-Integrated Sensors with the Help of FEM-Based Modeling
Sensors 15 (2015) 2, pp. 2336-2353, http://www.mdpi.com/1424-8220/15/2/2336

Brito Gadeschi, G.; Siewert, C.; Lintermann, A.; Meinke, M.; Schröder, W.:
Towards large multi-scale particle simulations with conjugate heat transfer on heterogeneous super computers
Transactions of the High Performance Computing Center, Stuttgart (HLRS), Springer International Publishing, Switzerland, 2015, High Performance Computing in Science and Engineering 14, pp. 307‑319

Brito Gadeschi, G.; Schneiders, L.; Meinke, M.; Schröder, W.:
A numerical method for multiphysics simulations based on hierarchical Cartesian grids
Journal of Fluid Science and Technology, 10 2015 (1), Paper No.14-00399

Klocke, F.; Harst, S.; Ehle, L.; Zeis, M.; Klink, A.:
Material Loadings during Electrochemical Machining (ECM) - a First Step for Process Signatures
Proceedings from the 18th International ESAFORM Conference on Material Forming (ESAFORM 2015), Key Engineering Materials Vol. 651-653 (2015) pp. 695-700

Klocke, F.; Schneider, S.; Harst, S.; Welling, D.; Klink, A.:
Energy-based approaches for multi-scale modelling of material loadings during Electric Discharge Machining (EDM)
Procedia CIRP 31 ( 2015 ) Proceeding of 15th CIRP Conference on Modelling of Machining Operations (pp. 191-196)

Meyer, D.; Redetzky, M.; Kämmler, J.:
The potential of cryogenic deep-rolling for producing near-optical surfaces
15th International Conference & Exhibition of the European Society for Precision Engineering & Nanotechnology, 01.06. – 05.06.2015 Leuven. Belgium, Conference Proceedings, pp. 21 - 22

Willert, M.; Riemer, O.:
Surface roughness of precision turned hardened steel
15th International Conference & Exhibition of the European Society for Precision Engineering & Nanotechnology, 01.06. – 05.06.2015 Leuven. Belgium, Conference Proceedings, pp. 381-382

Zeis, M.:
Modellierung des Abtragprozesses der elektrochemischen Senkbearbeitung von Triebwerksschaufeln
Dr.-Ing. Dissertation, RWTH Aachen, Apprimus Verlag, Aachen, 2015

Klocke, F.; Zeis, M.; Klink, A.:
Interdisciplinary modelling of the electrochemical machining process for engine blades
CIRP Annals - Manufacturing Technology 64 (2015) 1, pp. 217–220

Tausendfreund, A.; Stöbener, D.; Dumstorff, G.; Sarma, M.; Heinzel, C.; Lang, W.; Goch, G.:
Systems for locally resolved measurements of physical loads in manufacturing processes
CIRP Annals – Manufacturing Technology, Volume 64, 2015, pp. 495-498

Tausendfreund, A.; Stöbener, D.; Goch, G.:
Measuring technique for the detection of process force related component deformations in metal working manufacturing processes
5th Int. Conference on Distortion Engineering 2015, Bremen, 23-25 September 2015, pp. 355-364

Heinzel, C.; Meyer, D.; Kolkwitz, B.; Eckebrecht, J.:
Advanced approach for a demand-oriented fluid supply in grinding
CIRP Annals – Manufacturing Technology, Volume 64, 2015, pp. 333-336

Kochmann, J.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
Computational phase-field modeling of bulk microstructure evolution and direct FE-FFT-based micro-macro-transition
Proceedings of the 3rd ECCOMAS Young Investigators Conference on Computational Methods in Applied Sciences and 6th GACM Colloquium on Computational Mechanics

Dumstorff, G.; Lang, W.:
Printed Sensor for Integrating in Aluminum during Casting
AMA Conferences 2015 – SENSOR 2015, Nürnberg, pp. 580-583

Jermolajev, S.; Heinzel, C.; Brinksmeier E.:
Experimental and analytical investigation of workpiece thermal load during external cylindrical grinding
Procedia CIRP, Volume 31, 2015, pp. 465-470

Epp, J.:
In situ X-ray diffraction investigations of phase transformation and phase specific density evolution during quenching of low alloy steels
Proceedings of the 5th conference on distortion engineering, Bremen, Germany, sept 23rd -25th 2015. pp. 335-344

Frerichs, F.; Lübben, T.; Zoch, H-W.:
Interrelationship of strains and distortion of rectangular formed prisms
Frerichs F.; Lübben Th.; Zoch H-W.: Interrelationship of strains and distortion of rectangular formed prisms. Proc. of the 5th International Conference on Distortion Engineering, 2015 Sep. 23rd-25th, Bremen, Germany, pp. 129-140

Klocke, F.; Harst, S.; Ehle, L., Zeis, M.; Klink, A.:
Surface Integrity in ECM-Processes – An Analysis on Material Modifications Occurring during Electrochemical Machining
Proceedings of the 23rd CAPE Conference, 3-4 November 2015, Edinburgh, UK,

Klocke, F.; Harst, S.; Ehle, L., Zeis, M.; Klink, A.:
Influence of Material Microstructure on the Electrochemical Machinability of Steel 42CrMo4 and Inconel 718
International Symposium on Electrochemical Machining Technology (INSECT) 2015, 12. – 13. November 2015, Linz, Austria, pp. 43-51

Kochmann, J.; Wulfinghoff, S.; Svendsen, B.; Reese, S.:
Phase-field modeling of martensitic phase transformations in polycrystals coupled with crystal plasticity – A spectral-based approach
Proceedings in Applied Mathematics and Mechanics, 15: 317-318. doi: 10.1002/pamm.201510149

Wulfinghoff, S.; Reese, S.:
Efficient computational homogenization of simple elastoplastic microstructures using a shear band approach
Computer Methods in Applied Mechanics and Engineering, 298, pp. 350-372 (2016), doi: 10.1016/j.cma.2015.09.002

Gladkov, S.; Svendsen, B.:
Thermodynamic and rate variational formulation of models for inhomogeneous gradient materials with microstructure and application to phase field modeling
Acta Mechanica Sinica, 31(2), pp. 162-172

Wulfinghoff, S.; Reese, S.:
Efficient Computational Homogenization Of Simple Elasto-Plastic Microstructures Using A Modified Ritz-Galerkin Approach
Proceedings of the XIII International Conference on Computational Plasticity. Fundamentals and Applications (COMPLAS XIII). 1-3 September 2015, Barcelona, Spain, pp. 956-964

Brito Gadeschi, G.; Schneiders, L.; Siewert, C.; Lintermann, A.; Meinke, M.; Schröder, W.:
Large-Scale Simulations of Particle-laden flows
Inside, Innovatives Supercomputing in Deutschland, Spring 2015, Vol. 13, No. 1, pp. 25-28.

Sarma, M.; Reimers, M.; Dumstorff, G.; Lang W.:
Evaluating Thermo-Mechanical Stress Measured during Surface Grinding on a Sensor Integrated Workpiece Using COMSOL Multiphysics
https://www.comsol.de/paper/download/290741/sarma_paper.pdf CIRP 2015 COMSOL

Brinksmeier, E.; Klocke, F.; Lucca, D.A.; Sölter, J.; Meyer, D.:
Process signatures – a new approach to solve the inverse surface integrity problem in machining processes
Procedia CIRP 13 (2014), 429-434 DOI: 10.1016j.procir.2014.04.073

Jermolajev, S.; Brinksmeier, E.:
A new approach for the prediction of surface and subsurface properties after grinding
Periodical of Advanced Materials Research, Volume 1018, 2014, pp. 189-196

Brito Gadeschi, G.; Meinke, M.; Schroeder, W.:
A hierarchical Cartesian method for conjugated heat transfer
Proceedings of the 44th AIAA Fluid Dynamics Conference, 16-20 June 2014, Atlanta, USA, pp. 1-8

Heinzel, C.; Sölter, J.; Jermolajev, S.; Kolkwitz, B.; Brinksmeier, E.:
A versatile method to determine thermal limits in grinding
Proceedings of the 2nd CIRP Conference on Surface Integrity (CSI), Nottingham, UK, 28.05.-30.05.2014, Procedia CIRP 13 (2014), pp. 429-434

Heinzel, C.; Meyer D.; Kolkwitz, B.; Redetzky, M.:
Gezielte Randzonenbeeinflussung durch Fertigungsprozesse
Proceedings of the 3rd International Chemnitz Manufacturing Colloquium ICMC 2014, Chemnitz, Germany, 08.04.-09.04.2014, pp. 495-512

Dumstorff, G.; Lang, W.:
Failure of silicon substrates embedded in epoxy resin
http://www.sciencedirect.com/science/article/pii/S2212017314001893

Kuschel, S.; Sölter, J.; Brinksmeier, E.:
Analysing internal material loads in manufacturing processes, Vortrag: Analyse von Werkstoffbeanspruchungen in Fertigungsprozessen
WGP Congress 2014, 09.09.-10.09.2014, Erlangen, Advanced Materials Research Vol. 1018 (2014) pp. 83-90

Kochmann, J.; Rezai Mianroodi, J.; Svendsen, B.; Reese, S.:
Two-dimensional elastic phase-field simulation of fcc to bcc martensitic phase transformations in polycrystals
Proc. Appl. Math. Mech. 14 (2014), pp. 397-398

Dumstorff, G.; Lang, W.:
Strain gauges - volume embedding vs. surface application
Proceedings of the IEEE Sensors 2014, Valencia, Spain, November 2-5, 2014, IEEE Xplore Digital Library, pp. 1292 - 1295

Klocke, F.; Harst, S.; Schneider, S.; Zeis, M.; Klink, A.:
New Approach for an Energy-Based Multiscale Modeling of the Anodic Metal Dissolution during ECM
Proc. of the International Symposium on Electrochemical Machining Technology (INSECT) 2014, 13 – 14 November 2014, Saarbrücken, Germany, pp. 227-234

Klocke, F.; Schneider, S.:
Berechenbare Randzone
Industrie anzeiger 32.14 (S. 46-47)

Epp, J.:
Investigation of triaxial stress state in retained austenite during quenching of a low alloy steel by in situ X-ray diffraction
Advanced Materials Research 996 (2014), S. 525-531

Fechte-Heinen, R.:
Energy Methods in Material Modeling of Martensitic Phase Transformations
Habilitationsschrift, Ruhr-Universität Bochum (2013)

Hackl, K.; Junker, P.; Heinen, R.:
Variational modeling of shape memory alloys – an overview
Int. J. Mat. Res. 102, 643-651 DOI: 10.3139/146.110527

Hackl, K.; Heinen, R.:
A micromechanical model for pretextured polycrystalline shape-memory alloys including elastic anisotropy
Continuum Mech. Thermodyn. 19 (2008), 499-510 DOI: 10.1007/s00161-008-0067-z